We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Use Alt-Azimuth Mount: A Step-by-Step Guide for Beginners

Learn how to use alt-azimuth mount step by step: level it, align it, balance your scope and track objects across the sky. A clear beginner's guide.

Updated November 2026

An alt-azimuth mount moves your telescope up and down (altitude) and side to side (azimuth), which makes it the simplest way to point at any object in the sky. In this guide, you will learn how to use alt-azimuth mount hardware to set up level, balance your optical tube, find targets and follow them as the sky turns. Expect the whole process to take about 15 minutes once you have done it a few times.

Set Up the Mount on Stable Ground

Start with a firm, level surface. A concrete patio or a sturdy deck works well, while soft lawn lets the tripod sink and shift. Spread the tripod legs to a comfortable working height, then tighten the leg locks evenly. Most alt-azimuth tripods have a center tray or accessory bar; use it to hold eyepieces and a red flashlight within reach.

Shopping for one? See our guide: Celestron Alt Azimuth Mount Review: Features and Performance.

Next, level the mount head. Many owners use a small bubble level placed on the mount’s base plate or on a flat part of the head. Adjust the tripod legs until the bubble is centered in both directions. A mount that sits even a degree or two out of level will drift noticeably during a long observing session.

Balance and Attach Your Optical Tube

Loosen the altitude lock and azimuth lock before you mount the telescope. Attach the optical tube to the mounting saddle and tighten it firmly. Then slide the tube forward or backward in the saddle until it stays put when you release your hand with the altitude lock open. This is called balancing, and it protects the drive motors and keeps the scope from drooping on its own.

Balance matters more with heavier eyepieces, cameras or diagonals. Recheck it whenever you change accessories, especially if you plan to use a Barlow lens or a heavier eyepiece set. A balanced tube moves smoothly under light finger pressure, with no sudden drop or swing.

Find Targets and Track Them

For a basic manual session, loosen both locks, point the tube roughly at your target, then tighten the locks. Use the finderscope or a red-dot finder to center the object, and fine-tune with the slow-motion controls if your mount has them. Start with bright, easy targets like the Moon or Jupiter to build confidence before moving to fainter deep-sky objects.

Because the sky rotates, objects drift out of the eyepiece over minutes. On an alt-azimuth mount, you correct this by nudging both axes at once, since the motion is a combination of up-down and side-to-side. Motorized GoTo models can do this automatically once aligned. If you want more detail on how the axes interact, see Alt Azimuth Telescope Mount: How It Works and Who Should Use One.

Align a GoTo Mount

If your alt-azimuth mount has computerized GoTo, you will need an alignment routine before it can find objects. Most systems ask you to center two or three bright stars or planets in the eyepiece and confirm each one on the hand controller. Choose alignment stars that are well separated in the sky and far from the horizon for the best accuracy. After alignment, the mount will slew to targets from its database.

Refer to the manufacturer’s manual for the exact menu steps, since each controller uses different wording. For setup details on one common model, see Az3 Alt Azimuth Mount: Setup, Balancing and Tips for Beginners.

Common Mistakes and Tips

  • Skipping the level check. Even a slight tilt can cause field rotation and drift.
  • Leaving the locks partly tightened, which makes the tube jerk when you move it.
  • Forgetting to rebalance after adding a camera or heavy eyepiece.
  • Aligning on stars near the horizon, where atmospheric distortion throws off the mount’s position.
  • Trying to track fast-moving objects manually at high magnification without practice.

A red-light flashlight helps you read star charts and adjust controls without ruining your night vision. View on Amazon

A small bubble level or a dedicated mount leveling tool makes the setup step faster and more repeatable. View on Amazon

A planisphere or printed star chart helps you pick alignment stars and locate targets before you reach for the controller. View on Amazon

FAQ

Do I need to level an alt-azimuth mount every time?

Yes, check the level whenever you move the tripod or set up on a new surface. A quick bubble-level check takes under a minute and keeps tracking accurate.

Can I use an alt-azimuth mount for astrophotography?

Short exposures of bright objects are possible, but long exposures are difficult because the sky rotates relative to the mount. Equatorial mounts are generally preferred for long-exposure imaging.

Why does my object drift out of view so quickly?

The Earth’s rotation moves the sky continuously, and high magnification magnifies the drift. Lower the magnification, check your balance and make small corrections in both axes.

Conclusion

Once you level the mount, balance the tube and learn to nudge both axes, the alt-azimuth design becomes intuitive. Practice on bright targets first, and move to deeper objects as your confidence grows. With a little routine, you will spend more time observing and less time fiddling with the setup.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our telescopes & stargazing guides, checking product details against manufacturer specifications and owner feedback.

About the author

Colin Foster
Colin Foster

Colin Foster writes reviews and buying guides for Astronomy Site.