We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

T Rex Alt Azimuth Mount: Setup, Balancing and Tips for Beginners

Learn how a t rex alt azimuth mount works, how to set it up and balance it, and which common mistakes to avoid for smoother nights under the stars.

Updated November 2026

A t rex alt azimuth mount is a simple, manually operated base that moves a telescope up and down (altitude) and side to side (azimuth). This guide explains what each axis does, how to level and balance the mount, and how to avoid the errors that make tracking and framing harder than they need to be. Once you finish, you will be able to set up in the dark and follow objects without fighting the hardware.

How the Axes Work on a T Rex Alt Azimuth Mount

The mount rotates on two axes. The azimuth axis turns the whole assembly left and right around a vertical shaft. The altitude axis tilts the optical tube up and down. Because both motions are relative to the horizon, you can point at almost anything in the sky, but you will need to make small, frequent corrections as Earth rotates. For a fuller explanation of the geometry, see What Is Alt Azimuth Mount? How It Works for Beginners (2026).

Shopping for one? See our guide: Celestron Alt Azimuth Mount Review: Features and Performance.

Setting Up and Leveling the Base

Stable setup matters more than most beginners expect. A tripod that wobbles will blur the image every time you touch the focuser.

  1. Extend the tripod legs so the top plate sits at a comfortable height, roughly at your waist or chest.
  2. Spread the legs wide and lock them. Set the tripod on firm ground, not grass that may sink.
  3. Use a bubble level on the mount head, not the tripod, and adjust the leg lengths until the bubble is centered in both directions.
  4. Tighten all knobs and bolts, then check the level again after you attach the tube.

Manufacturers generally specify a maximum payload for each mount. Stay well under that figure with your tube, eyepiece and any camera, because heavy loads on a light head cause drift and vibration.

Balancing the Optical Tube

Balance reduces strain on the altitude motor and lets the tube hold its position when you let go. Loosen the altitude lock, slide the tube in its rings until it sits level when you release it, then tighten the rings. Check balance at both ends of the altitude travel. If the tube drops toward the eyepiece or the rear, shift the weight forward or back. A balanced tube feels still and lets you make fine adjustments with one hand.

Finding and Tracking Objects

Start with a low-power eyepiece to find targets, then switch to higher power once the object is centered. Use the slow-motion controls rather than pushing the tube directly. Because the mount tracks in altitude and azimuth, the object will drift diagonally across the field. Nudge both axes together every minute or two. For sky-chart basics and target selection, consider reading How to Use Alt-Azimuth Mount: A Step-by-Step Guide for Beginners.

Common Mistakes and Tips

  • Skipping the level check after tightening the tube rings.
  • Overloading the head with accessories that exceed the rated payload.
  • Setting up on soft or sloped ground, which causes slow creep during observing.
  • Forgetting that a balanced tube reduces both strain and star drift.
  • Pushing the tube by hand at high magnification instead of using the fine controls.

A sturdy tripod with a stable top plate reduces the vibration that makes the mount harder to use. View on Amazon

A small bubble level or a level-indicating accessory helps you get the base truly horizontal, which is the foundation for accurate movement. View on Amazon

FAQ

Is a t rex alt azimuth mount good for beginners?

Yes. Its two-axis design is straightforward, and it suits visual observing of planets, the Moon and bright deep-sky objects. Expect to make frequent manual corrections.

Why does my view drift so quickly?

Drift is normal on an alt-azimuth mount because the sky rotates diagonally relative to the axes. Check that the base is level and the tube is balanced, then correct as needed.

Can I use a camera on this mount?

Short exposures of the Moon and planets are possible, but long exposures will blur without a tracking system. Check the rated payload before adding any camera equipment.

Conclusion

A t rex alt azimuth mount rewards careful leveling and balance. Set the base on firm ground, balance the tube and use the slow-motion controls. With those habits, you will spend more time observing and less time correcting.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our telescopes & stargazing guides, checking product details against manufacturer specifications and owner feedback.

About the author

Colin Foster
Colin Foster

Colin Foster writes reviews and buying guides for Astronomy Site.