We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

ZWO ASIAIR Plus Wireless Camera Controller for Astrophotography: Setup Guide

Learn how the ZWO ASIAIR Plus wireless camera controller for astrophotography works, from setup and polar alignment to guiding and capturing your first deep-sky

Updated November 2026

The ZWO ASIAIR Plus wireless camera controller for astrophotography is a small computer that sits on your mount or telescope and runs your imaging session from a phone, tablet or laptop. In this guide you will learn how to connect it, align your mount, start guiding and begin capturing usable frames without fumbling with a laptop under a dark sky. The steps below assume you already have a camera, a mount and a telescope or lens.

What the ASIAIR Plus Does in Your Setup

The ASIAIR Plus replaces a dedicated laptop in many imaging setups. It connects to your camera, guide camera, focuser and mount, then runs the exposure sequence, plate solving and autoguiding itself. You control it through the ASIAIR app over a Wi-Fi network it creates. This reduces cable clutter and keeps your setup lighter, which matters when you are working alone in the dark.

Because the controller handles the sequencing, you can leave it running while you step away. Check the official ZWO documentation for the current list of supported cameras, mounts and firmware versions before you buy or set up hardware.

Step-by-Step Setup

  1. Mount the ASIAIR Plus on the mount or a nearby bracket, and connect power from a battery pack rated for your session length.
  2. Connect the imaging camera, guide camera, focuser and mount with the cables specified in the ASIAIR manual. Confirm each device appears in the app before you go further.
  3. Join the ASIAIR Wi-Fi network from your phone or tablet, then open the ASIAIR app and check the connected devices list.
  4. Set your site location and time, then point the mount roughly toward the north or south celestial pole for polar alignment.
  5. Run the built-in polar alignment routine. It uses plate solving to measure how far your mount axis is off and gives you adjustment directions.
  6. Choose a target, let the app plate solve the field, then start autoguiding and check that the guide star stays steady.
  7. Build an imaging sequence with exposure length, gain, frame count and dithering, then start the run.

Polar Alignment and Guiding

Good polar alignment is what makes long exposures possible. Tracking errors show up as elongated stars, so keep the polar alignment error low before you start guiding. Many imagers aim for a residual error of a few arcminutes or less, though your target exposure length and focal length determine how tight you need to be. Re-run the alignment if you move the mount or the temperature changes significantly.

Autoguiding corrects the small drift that remains. Start with a guide star that is bright enough to track but not saturated, and choose a guide camera with enough resolution for your focal length. Dithering between frames, which shifts the image slightly, helps reject hot pixels and walking noise in the final stack.

Common Mistakes to Avoid

  • Skipping polar alignment and blaming guiding for elongated stars.
  • Running out of battery mid-session. Calculate your power draw and bring a spare.
  • Setting exposures too long before confirming focus and guiding are stable.
  • Forgetting to update firmware before a session, which can cause connection problems in the field.
  • Leaving dew heaters off on humid nights, which can fog your optics.
  • A dedicated guide camera gives the ASIAIR a sensitive sensor to track a guide star, which tightens your tracking over long exposures. View on Amazon
  • A stable power bank keeps the controller and cameras running through a full night in the field. View on Amazon
  • A USB hub with powered ports helps when you need several devices connected to one controller without voltage drops. View on Amazon

If you are still deciding which imaging camera pairs best with this controller, see 5 Best ZWO Cameras for Astrophotography Picks Compared (2026). For a broader look at how telescopes and lenses compare for this kind of work, read Telescope vs Camera Lens for Astrophotography: A Practical Guide (2026).

FAQ

Do I need a laptop to use the ZWO ASIAIR Plus?

No. The ASIAIR Plus runs the sequencing, plate solving and guiding on its own, and you control it from a phone or tablet over its Wi-Fi network. A laptop is optional for review or processing.

How accurate does polar alignment need to be?

It depends on your focal length and exposure length. Longer exposures and longer focal lengths demand tighter alignment, so use the built-in routine and aim for the lowest error your setup allows.

Can the ASIAIR Plus work with any camera?

It supports a specific list of cameras, mounts and focusers. Check the current compatibility list on the official ZWO site before you buy.

Conclusion

With the ASIAIR Plus, you can run a full imaging session from a phone while the controller handles alignment, guiding and sequencing. Set up carefully, check polar alignment and keep power and firmware in order, and you will spend more of the night capturing frames. Start with a short test session before committing to a long run.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our telescopes & stargazing guides, checking product details against manufacturer specifications and owner feedback.

About the author

Colin Foster
Colin Foster

Colin Foster writes reviews and buying guides for Astronomy Site.