Tasco Spacestation 700x60mm Refractor Telescope: Setup and Use Guide
Learn how to set up, aim and use a Tasco Spacestation 700x60mm refractor telescope, from assembly and eyepiece choice to finding your first planets and Moon tar
Updated November 2026
The tasco spacestation 700x60mm refractor telescope is a small, lightweight scope built for casual observing of the Moon, bright planets and a handful of star clusters. This guide walks you through assembly, first-night alignment, eyepiece swaps and realistic expectations, so you can get a clear view of your first target within about 30 minutes of opening the box. Its stated 700 mm focal length and 60 mm aperture define what you will and will not see, so we start there.
Understand What the Specs Actually Mean
The 60 mm aperture is the lens diameter, and it sets how much light the scope gathers and how sharp fine detail can be. The 700 mm focal length, combined with the eyepieces supplied, determines magnification. Manufacturers typically list the included eyepieces as delivering magnifications in the range of roughly 35x to 140x, depending on the eyepiece focal length you use. Expect the Moon, Jupiter’s cloud bands and Saturn’s rings to be recognizable, while faint galaxies and nebulae will look like faint smudges or nothing at all under light-polluted skies.
Assemble and Align the Telescope
Mount the tripod on level ground, attach the altazimuth mount, then slide the optical tube into its holder and tighten the clamps just enough to hold it firmly. Insert the lowest-power eyepiece into the focuser and lock it. Start with a daytime target such as a distant rooftop or tree, because it is far easier to focus on a stationary object with good contrast.
- Set the tripod legs to a comfortable height so you can look through the eyepiece without bending awkwardly.
- Point the tube at your daytime target and rotate the focuser knob slowly until the image sharpens.
- Center the target in the finder scope, then recheck it through the main eyepiece.
- Repeat the focus step after every eyepiece change, since each one shifts the focal point slightly.
Find and Observe Your First Targets
The Moon is the most rewarding first target because it is bright, easy to locate and shows crater rims and the terminator, the line between lunar day and night, in sharp relief. Use a medium-power eyepiece and move the scope slowly, since high magnification makes small handling movements look large. Jupiter is the next easiest target. Once it is centered, switch to a higher-power eyepiece and look for the cloud belts and the four Galilean moons, which appear as small points of light near the planet.
For Saturn, watch for a pale yellowish disk with ring structure on either side. If the rings look like thin lines or ears, the scope is working; it simply means the rings are tilted in a way that makes them appear narrow. Deep-sky targets such as the Pleiades or the Orion Nebula work best from dark sites, so wait until your eyes have had 20 to 30 minutes to adapt before judging them. A related read: Reflector or Refractor Telescope for Beginner: Which Should You Choose?.
Choose the Right Eyepiece for Each Target
Low power gives a wide field and bright image, ideal for finding targets and viewing extended objects. Higher power reveals detail but dims the image and magnifies atmospheric shake. A practical rule is to begin at low power, then step up only as far as the image stays steady and reasonably bright. Many owners find that the sweet spot for planets sits in the middle of the supplied range, while the Moon tolerates the highest powers well on steady nights.
| Target | Suggested Power Range | What to Look For |
|---|---|---|
| Moon | Low to medium | Crater rims, terminator shadows |
| Jupiter | Medium to high | Cloud bands, Galilean moons |
| Saturn | Medium to high | Rings, the yellow disk |
| Star clusters | Low | Scattered bright stars |
Common Mistakes
- Trying to observe at the highest magnification first, which makes the image dim and unsteady.
- Forgetting to refocus after changing eyepieces.
- Setting up on soft ground, where the tripod drifts and the view keeps shifting.
- Expecting faint galaxies to look like photographs; they appear as gray smudges at best.
- Observing from a brightly lit backyard instead of a darker spot away from streetlights.
Recommended Gear
A red-light headlamp helps you read star charts and adjust the scope without ruining your night vision. View on Amazon
A planisphere or basic star chart makes it much easier to identify constellations and planets before you start moving the scope. View on Amazon
A sturdy, level observing table or stool lets you sit comfortably at the eyepiece during longer sessions. View on Amazon
For more context on this model, see Tasco Spacestation Refractor Telescope Review: Is It Worth It? and Tasco Spacestation 60x700mm Refractor Telescope: 5 Best Picks Compared. If you are weighing it against other small refractors, Tasco 60mm Refractor Telescope: 5 Best Picks Compared for 2026 covers similar options, and Reflector vs Refractor Telescope: Which Is Better? (2026) explains the tradeoffs between optical designs.
FAQ
Can the Tasco Spacestation 700x60mm show planets?
Yes. Jupiter’s cloud bands, its largest moons and Saturn’s rings are generally visible at the supplied magnifications, though fine detail will be modest.
Do I need a dark sky to use it?
Not for the Moon and planets, which are bright enough to view from suburban areas. Deep-sky objects benefit greatly from darker sites.
How long does setup take?
Most first-time users can assemble the tripod and tube and reach focus on a daytime target within about 30 minutes.
Conclusion
The tasco spacestation 700x60mm refractor telescope rewards patient, low-power observing, especially on the Moon and bright planets. Set it up on firm ground, focus on a daytime target first and step up in magnification only when the image stays steady. With those habits, your first sessions should deliver clear, satisfying views.
Ready to choose one?
