We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Celestron Starsense Explorer Lt 70az Smartphone App-enabled Refractor Telescope: A Practical Guide (2026)

Learn how the Celestron StarSense Explorer LT 70AZ smartphone app-enabled refractor telescope works, what it shows, and how to set it up for your first night ou

Updated November 2026

The celestron starsense explorer lt 70az smartphone app-enabled refractor telescope pairs a small 70mm refractor with a phone app that finds objects for you. In this guide you will set up the telescope, run the StarSense alignment, and learn what to expect from the views of the Moon, planets and bright star clusters. Plan on about 30 minutes for your first setup.

What the StarSense Explorer LT 70AZ Shows You

This is an altazimuth refractor, meaning it moves up-down and left-right with no tracking motor. Its 70mm objective is best suited to bright targets: the Moon’s craters and terminator, the four large moons of Jupiter, the phases of Venus, and open clusters such as the Pleiades. Galaxies and nebulae will appear as faint smudges at best, so set expectations accordingly. Manufacturers specify a focal length of about 700mm, which gives moderate magnification with the included eyepieces.

Shopping for one? See our guide: 4 Best Starsense Explorer Dx 102az Smartphone App-enabled Refractor Telescopes (2026): Our Picks.

Setting Up the Telescope Before Your First Night

Assemble the tripod on level ground and attach the altazimuth mount. Insert the eyepiece into the diagonal, then install the finderscope. Do this in daylight so you can check focus on a distant object. Pick a target that is at least 100 yards away and focus until the edges look sharp.

  1. Mount the optical tube to the altazimuth mount and tighten the clamps.
  2. Level the tripod as closely as you can by eye.
  3. Insert the low-power eyepiece and focus on a distant daytime object.
  4. Charge your phone and install the Celestron SkyPortal app before going outside.
  5. Turn on Bluetooth, then open the app and select the StarSense Explorer LT 70AZ.

Running the StarSense Alignment

StarSense uses your phone’s camera to read the sky and work out where the telescope is pointing. The alignment is the step most beginners rush, and it is the one that matters most. Follow the on-screen prompts, and point the telescope at the star or area the app asks for. Center the star in the finderscope or eyepiece before pressing confirm. Once the app reports a successful alignment, you can select an object from its database and follow the arrows to find it.

Clear, dark skies make alignment easier. Light pollution and a bright Moon can cause the phone camera to struggle, so try again from a darker spot or wait until the Moon is lower. The app’s sky map and the telescope’s actual view should agree once alignment is complete.

Getting the Best Views from Your Session

Start with the Moon, since it is bright and forgiving. Then move to Jupiter and Saturn if they are up. Use a higher-power eyepiece only after the image is steady at low power. Let your eyes dark-adapt for 15 to 20 minutes, and keep one eye open when you are not looking through the eyepiece.

Factors That Affect Image Quality

Factor Effect on the View What to Do
Light pollution Fainter objects vanish Observe from a darker site
Atmospheric steadiness Planets shimmer Wait for calmer air or use lower power
Moon phase Bright Moon washes out deep-sky targets Pick Moon-free nights for galaxies

Common Mistakes

  • Skipping the daytime focus check, which leaves you fumbling in the dark.
  • Rushing the StarSense alignment instead of centering the reference star carefully.
  • Using high-power eyepieces before the image is steady.
  • Expecting galaxies to look like photographs. Most will look faint and gray.
  • Forgetting to keep the phone charged, since the app depends on Bluetooth.
  • Red-light headlamp: preserves your night vision while you adjust the telescope. View on Amazon
  • Planisphere: a simple star chart that helps you learn constellations without a screen. View on Amazon
  • Dew shield or dew strap: helps keep the front lens from fogging on cool, humid nights. View on Amazon

FAQ

Does the StarSense Explorer LT 70AZ work without a phone?

The telescope still works as a manual refractor, but the StarSense guidance depends on the phone app and its camera. You can still find objects by star-hopping with the finderscope.

What is the best target for a first session?

The Moon is the easiest and most rewarding. Jupiter’s moons and the Pleiades are good follow-up targets.

Do I need to level the tripod perfectly?

No. Get it reasonably level so the mount moves smoothly, and rely on the app’s alignment to handle the rest. Check the official Celestron documentation for current setup recommendations.

Conclusion

With a careful daytime focus, a patient StarSense alignment and a dark sky, the celestron starsense explorer lt 70az smartphone app-enabled refractor telescope can show you the Moon, planets and bright clusters with little frustration. Start small, keep your expectations realistic, and build from there. Clear skies.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our telescopes & stargazing guides, checking product details against manufacturer specifications and owner feedback.

About the author

Claire Whitaker
Claire Whitaker

Claire Whitaker writes reviews and buying guides for Astronomy Site.